PKA 7.2.2.4 Packet Tracer - Configuring Basic EIGRP with IPv4.

Konfigurasi Router R1

R1>en
R1#conf t
Enter configuration commands, one per line.  End with CNTL/Z.

R1(config)#router eigrp 1
R1(config-router)#netw
R1(config-router)#network 172.16.1.0 0.0.0.255
R1(config-router)#network 172.16.3.0 0.0.0.3
R1(config-router)#network 192.168.10.4 0.0.0.3
R1(config-router)#passive-interface g0/0
R1(config-router)#no auto-summary
R1(config-router)#exit


Konfigurasi Router R2

R2>en
R2#conf t
Enter configuration commands, one per line.  End with CNTL/Z.

R2(config)#router eigrp 1
R2(config-router)#network 172.16.2.0 0.0.0.255
R2(config-router)#network 172.16.3.1 0.0.0.3
R2(config-router)#network 192.168.10.8 0.0.0.3
R2(config-router)#passive-interface g0/0
R2(config-router)#no auto-summary
R2(config-router)#exit


Konfigurasi Router R3

R3>en
R3#conf t
Enter configuration commands, one per line.  End with CNTL/Z.

R3(config)#router eigrp 1
R3(config-router)#network 192.168.1.0 0.0.0.255
R3(config-router)#network 192.168.10.5 0.0.0.3
R3(config-router)#network 192.168.10.9 0.0.0.3
R3(config-router)#passive-interface g0/0
R3(config-router)#no auto-summary
R3(config-router)#exit

PKA 7.4.3.4 Packet Tracer - Configuring Basic EIGRP with IPv6 Routing.

Konfigurasi Router R1

R1>en
R1#conf t
Enter configuration commands, one per line.  End with CNTL/Z.

R1(config)#ipv6 unicast-routing
R1(config)#ipv6 router eigrp 1
R1(config-rtr)#no shutdown
R1(config-rtr)#exit

R1(config)#interface gigabitEthernet 0/0
R1(config-if)#ipv6 eigrp 1
R1(config-if)#exit
R1(config)#interface serial 0/0/0
R1(config-if)#ipv6 eigrp 1
R1(config-if)#exit
R1(config)#interface serial 0/0/1
R1(config-if)#ipv6 eigrp 1
R1(config-if)#exit


Konfigurasi Router R2

R2>en
R2#conf t
Enter configuration commands, one per line.  End with CNTL/Z.

R2(config)#ipv6 unicast-routing
R2(config)#ipv6 router eigrp 1
R2(config-rtr)#no shutdown
R2(config-rtr)#exit

R2(config)#interface gigabitEthernet 0/0
R2(config-if)#ipv6 eigrp 1
R2(config-if)#exit
R2(config)#interface serial 0/0/0
R2(config-if)#ipv6 eigrp 1
R2(config-if)#exit
R2(config)#interface serial 0/0/1
R2(config-if)#ipv6 eigrp 1
R2(config-if)#exit
R2(config)#


Konfigurasi Router R3

R3>en
R3#conf t
Enter configuration commands, one per line.  End with CNTL/Z.

R3(config)#ipv6 unicast-routing
R3(config)#ipv6 router eigrp 1
R3(config-rtr)#no shutdown
R3(config-rtr)#exit

R3(config)#interface gigabitEthernet 0/0
R3(config-if)#ipv6 ei
R3(config-if)#ipv6 eigrp 1
R3(config-if)#exit
R3(config)#interface serial 0/0/0
R3(config-if)#ipv6 eigrp 1
R3(config-if)#exit
R3(config)#interface serial 0/0/1
R3(config-if)#ipv6 eigrp 1
R3(config-if)#exit
R3(config)#

PKA 1.3.1.3 Packet Tracer - Skills Integration Challenge.

Cnt-Sw

Cnt-Sw>ena

Cnt-Sw#conf t

Cnt-Sw (config)#int vlan 60

Cnt-Sw(config-if)#ip address 192.168.45.34 255.255.255.240

Cnt-Sw(config-if)#exit

Cnt-Sw(config)#ip default-gateway 192.168.45.33

Cnt-Sw(config)#ip domain-name cisco.com

Cnt-Sw(config)#crypto key generate rsa

How many bits in the modulus [512]: 1024

Cnt-Sw(config)#ip ssh version 2

Cnt-Sw(config)#ip ssh authentication-retries 2

Cnt-Sw(config)#ip ssh time-out 60

Cnt-Sw(config)#line vty 0 15

Cnt-Sw(config-line)#exit

Cnt-Sw(config)#username CAdmin password itsasecret

Cnt-Sw(config)#line vty 0 15

Cnt-Sw(config-line)#login local

Cnt-Sw(config-line)#transport input ssh

Cnt-Sw(config-line)#exit

Cnt-Sw(config)#service password-encryption

Cnt-Sw(config)#vlan 15

Cnt-Sw(config-vlan)#name Servers

Cnt-Sw(config-vlan)#vlan 30

Cnt-Sw(config-vlan)#name PCs

Cnt-Sw(config-vlan)#vlan 45

Cnt-Sw(config-vlan)#name Native

Cnt-Sw(config-vlan)#vlan 60

Cnt-Sw(config-vlan)#name Management

Cnt-Sw(config-vlan)#exit

Cnt-Sw(config)#int range fa0/11-20

Cnt-Sw(config-if-range)#switchport mode access

Cnt-Sw(config-if-range)#switchport access vlan 15

Cnt-Sw(config-if-range)#int range fa0/1-10

Cnt-Sw(config-if-range)#switchport mode access

Cnt-Sw(config-if-range)#switchport access vlan 30

Cnt-Sw(config-if-range)#int g0/1

Cnt-Sw(config-if)#switchport mode trunk

Cnt-Sw(config-if)#switchport trunk native vlan 45

Cnt-Sw(config-if)#exit

Cnt-Sw(config)#int fa0/1

Cnt-Sw(config-if)#switchport port-security maximum 2

Cnt-Sw(config-if)#switchport port-security mac-address sticky

Cnt-Sw(config-if)#switchport port-security violation restrict

Cnt-Sw(config-if)#exit

Cnt-Sw(config)#int range fa0/2-10, fa0/12-24, g0/2

Cnt-Sw(config-if-range)#shut

Cnt-Sw(config-if-range)#

Central

Central#sh run

Central#conf t

Central(config)#int g0/0

Central(config-if)#no shutdown

Central(config-if)#exit

Central(config)#ip route 0.0.0.0 0.0.0.0 s0/1/0

Central(config)#router ospf 1

Central(config-router)#default-information originate

Central(config-router)#exit

Central(config)#access-list 1 permit 192.168.45.0 0.0.0.255

Central(config)#exit

Central#conf t

Central(config)#router ospf 1

Central(config-router)#exit

Central(config)#access-list permit 192.168.45.0 0.0.0.255

Central(config)#ip nat pool public 64.100.32.56 64.100.32.57 netmask

Central(config)#ip nat inside source static 192.168.45.66 64.100.32.58

Central(config)#int g0/0.15

Central(config-subif)#ip nat inside

Central(config-subif)#int g0/0.30

Central(config-subif)#ip nat inside

Central(config-subif)#int g0/0.45

Central(config-subif)#ip nat inside

Central(config-subif)#int g0/0.60

Central(config-subif)#ip nat inside

Central(config-subif)#int g0/0

Central(config-if)#ip nat inside

Central(config-if)#int s0/0/1

Central(config-if)#ip nat inside

Central(config-if)#int s0/0/1

Central(config-if)#ip nat outside

PKA 2.3.2.2 Packet Tracer - Configuring Rapid PVST+.

Konfigurasi pada Switch

S1

S1>ena

S1#conf t

Enter configuration commands, one per line. End with CNTL/Z.

S1(config)#vlan 10

S1(config-vlan)#vlan 20

S1(config-vlan)#vlan 30

S1(config-vlan)#vlan 40

S1(config-vlan)#vlan 50

S1(config-vlan)#vlan 60

S1(config-vlan)#vlan 70

S1(config-vlan)#vlan 80

S1(config-vlan)#vlan 99

S1(config-vlan)#exit

S1(config-vlan)#int vlan 99

S1(config-if)#ip address 172.17.99.11 255.255.255.0

S1(config)#int range fa0/1-4

S1(config-if-range)#sw

S1(config-if-range)#switchport mode trunk

S1(config-if-range)#switchport trunk native vlan 99

S1(config-if-range)#end

S1#ping 172.17.99.12

S1#ping 172.17.99.13

S1#conf t

S1(config)#spanning-tree mode rapid-pvst

S1(config)#spanning-tree vlan 1 root primary

S1(config)#spanning-tree vlan 10 root primary

S1(config)#spanning-tree vlan 30 root primary

S1(config)#spanning-tree vlan 50 root primary

S1(config)#spanning-tree vlan 70 root primary

S2

S2>ena

S2#conf t

Enter configuration commands, one per line. End with CNTL/Z.

S2(config)#int range fa0/11, fa0/18, fa0/6

S2(config-if-range)#switchport mode access

S2(config-if-range)#no shutdown

S2(config-if-range)#exit

S2(config)#vlan 10

S2(config-vlan)#vlan 20

S2(config-vlan)#vlan 30

S2(config-vlan)#vlan 40

S2(config-vlan)#vlan 50

S2(config-vlan)#vlan 60

S2(config-vlan)#vlan 70

S2(config-vlan)#vlan 80

S2(config-vlan)#vlan 99

S2(config-vlan)#exit

S2(config)#int fa0/6

S2(config-if)#switchport access vlan 30

S2(config-if)#int fa0/18

S2(config-if)#switchport access vlan 20

S2(config-if)#int fa0/11

S2(config-if)#switchport access vlan 10

S2(config-if)#exit

S2(config)#int vlan 99

S2(config-if)#ip address 172.17.99.12 255.255.255.0

S2(config-if)#end

S2#show vlan brief

S2#conf t

S2(config)#int range fa0/1-4

S2(config-if-range)#switchport mode trunk

S2(config-if-range)#switchport trunk native vlan 99

S2(config-if-range)#exit

S2(config)#spanning-tree mode rapid-pvst

S2(config)#spanning-tree vlan 1 root secondary

S2(config)#spanning-tree vlan 10 root secondary

S2(config)#spanning-tree vlan 20 root secondary

S2(config)#spanning-tree vlan 30 root secondary

S2(config)#spanning-tree vlan 40 root secondary

S2(config)#spanning-tree vlan 50 root secondary

S2(config)#spanning-tree vlan 60 root secondary

S2(config)#spanning-tree vlan 70 root secondary

S2(config)#spanning-tree vlan 80 root secondary

S2(config)#spanning-tree vlan 99 root secondary

S2(config)#int range fa0/11, fa0/18, fa0/6

S2(config-if-range)#spanning-tree portfast

S2(config-if-range)#int range fa0/11, fa0/18, fa0/6

S2(config-if-range)#spanning-tree bpduguard enable

S3

S3>ena

S3#conf t

Enter configuration commands, one per line. End with CNTL/Z.

S3(config)#vlan 10

S3(config-vlan)#vlan 20

S3(config-vlan)#vlan 30

S3(config-vlan)#vlan 40

S3(config-vlan)#vlan 50

S3(config-vlan)#vlan 60

S3(config-vlan)#vlan 70

S3(config-vlan)#vlan 80

S3(config-vlan)#vlan 99

S3(config-vlan)#exit

S3(config)#int vlan 99

S3(config-if)#ip address 172.17.99.13 255.255.255.0

S3(config-if)#exit

S3(config)#int range fa0/1-4

S3(config-if-range)#switchport mode trunk

S3(config-if-range)#switchport trunk native vlan 99

S3(config-if-range)#exit

S3(config)#spanning-tree mode rapid-pvst

S3(config)#spanning-tree vlan 20 root primary

S3(config)#spanning-tree vlan 40 root primary

S3(config)#spanning-tree vlan 60 root primary

S3(config)#spanning-tree vlan 80 root primary

S3(config)#spanning-tree vlan 99 root primary

PKA 8.1.2.5 Packet Tracer - Configuring EIGRP Manual Summary Routes for IPv4 and IPv6.

Konfigurasi Router Brach-1

Branch-1(config)#int s0/0/0
Branch-1(config-if)#ip sum
Branch-1(config-if)#ip summary-address ei
Branch-1(config-if)#ip summary-address eigrp 1 172.31.8.0 255.255.252.0


Konfigurasi Router Brach-2

Branch-2>en
Branch-2#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Branch-2(config)#int se0/0/1
Branch-2(config-if)#ip su
Branch-2(config-if)#ip summary-address ei
Branch-2(config-if)#ip summary-address eigrp 1 172.31.12.0 255.255.252.0


Konfigurasi Router Ipv4-Edge
IPv4-Edge>en
IPv4-Edge#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
IPv4-Edge(config)#int se0/1/0
IPv4-Edge(config-if)#ip su
IPv4-Edge(config-if)#ip summary-address ei
IPv4-Edge(config-if)#ip summary-address eigrp 1 172.31.8.0 255.255.248.0

PKA 9.3.1.4 Packet Tracer - Skills Integration Challenge

R1

R1>ena

R1#conf t

R1(config)#router ospf 1

R1(config-router)#router

R1(config-router)#router-id 1.1.1.1

R1(config-router)#network 172.31.24.0 0.0.3.255 area 10

R1(config-router)#network 172.31.31.248 0.0.0.3 area 0

R1(config-router)#network 172.31.31.252 0.0.0.3 area 0

R1(config-router)#passive-interface g0/0

R1(config-router)#passive-interface g0/1

R1(config-router)#exit

R1(config)#ip route 0.0.0.0 0.0.0.0 s0/1/0

R1(config)#router ospf 1

R1(config-router)#default-information originate

R1(config-router)#area 0 authentication message-digest

R1(config-router)#exit

R1(config)#int se0/0/0

R1(config-if)#ip ospf message-digest-key 1 md5 cisco123

R1(config-if)#exit

R1(config)#int se0/0/1

R1(config-if)#ip ospf message-digest-key 1 md5 cisco123

R1(config-if)#

R1>ena

R1#conf t

R1(config)#access-list 1 permit 172.31.24.1 0.0.0.0

R1(config)#line vty 0 15

R1(config-line)#access-class 1 in

R1(config-line)#

R2

R2>ena

R2#conf t

R2(config)#router ospf 1

R2(config-router)#router-id 2.2.2.2

R2(config-router)#network 172.31.28.0 0.0.1.255 area 20

R2(config-router)#network 172.31.31.248 0.0.0.3 area 0

R2(config-router)#passive-interface g0/0

R2(config-router)#passive-interface g0/1

R2(config-router)#area 0 authentication message-digest

R2(config-router)#exit

R2(config)#int se0/0/0

R2(config-if)#ip ospf message-digest-key 1 md5 cisco123

R2(config-if)#

00:27:37: %OSPF-5-ADJCHG: Process 1, Nbr 1.1.1.1 on Serial0/0/0 from LOADING to FULL, Loading Done

R3

R3>ena

R3#conf t

R3(config)#int g0/0

R3(config-if)#ip address 172.31.30.126 255.255.255.128

R3(config-if)#no shutdown

R3(config-if)#exit

R3(config)#int g0/1

R3(config-if)#ip address 172.31.30.254 255.255.255.128

R3(config-if)#no shutdown

R3(config-if)#

R3>ena

R3#conf t

R3(config)#router ospf 1

R3(config-router)#router-id 3.3.3.3

R3(config-router)#network 172.31.30.0 0.0.0.255 area 30

R3(config-router)#network 172.31.31.252 0.0.0.3 area 0

R3(config-router)#passive-interface g0/0

R3(config-router)#passive-interface g0/1

R3(config-router)#exit

R3(config)#router ospf 1

R3(config-router)#area 0 authentication message-digest

R3(config-router)#exit

R3(config)#int se0/0/1

R3(config-if)#ip ospf message-digest-key 1 md5 cisco123

R3(config-if)#

00:31:01: %OSPF-5-ADJCHG: Process 1, Nbr 1.1.1.1 on Serial0/0/1 from LOADING to FULL, Loading Done

R3(config-if)#do show ip route ospf

IP Untuk PC-E

 IP Untuk PC-F

Ipconfig

PKA 8.1.3.4 Packet Tracer - Propagating a Default Route in EIGRP for IPv4 and IPv6

 

Konfigurasi Router IPV4-EGE

IPv4-Edge(config)#ip route 0.0.0.0 0.0.0.0 serial 0/1/0
IPv4-Edge(config)#router eigrp 1
IPv4-Edge(config-router)#redistribute static

Konfigurasi Router IPV6-EDGE

IPv6-Edge(config)#ipv6 route ::/0 serial 0/1/0
IPv6-Edge(config)#ipv6 router eigrp 1
IPv6-Edge(config-rtr)#redistribute static